1990	Toshiba MK1122FC
	First glass disk

Why it’s important

The previous disk material, aluminum, is too soft to take the all the physical abuse in the mobile market. Aluminum’s replacement by glass further enabled the growth of HDD’s into the mobile market. Hoya provided the first such media.


Discussion

Development Outline:
In October, 1989, Toshiba started developing HDDs which featured compact design with high capacity, high performance, high power-saving and high environmental resistance for mobile office automation equipment, especially for Note PC.

At that time, Conner Peripherals had already announced a 2.5” HDD with a single aluminum disk and it was already in the market; therefore, we would set our goal as developing a 40
MB+ HDD with a single disk.

In order to achieve a high capacity HDD, it was essential to use over 100Mbpsi, high areal density. We matched up with a 50 turn thin-film head and glass media with low-roughness and smooth surface to implement 0.1μm head flying height, and it worked.In November 1989, Yamaha, Hoya and Toshiba decided to co-develop the head and media combination. When introducing glass media to the market, there was fear that the disk might be broken while handling, assembling and testing using a punch test, so we conducted a
significantly demanding crack check test by using engineering samples and functional samples. As a result, there was no breakage found. Rather, the conclusion told us that glass media was several times stronger than aluminum media in reaction to scratch at head collision in non-operating conditions. Thus, shock resistance performance level was beyond our expected spec of 100G, which proved glass media’s durability is beneficial and afterward, the result became a selling point for the glass media HDD. But then, since glass media had a smaller coefficient thermal expansion than aluminum media, we had to change the spindle motor material from aluminum to stainless steel to keep deformation caused by temperature change at a minimum.

We focused on the following to ensure the machine credibility of the HDD:

-Anti HDI ( Head Disk Interference)
-CSS (Contact Start Stop)
-Durability
-Anti-Stiction
-Anti Corrosion

SiO2, the unique Hoya Glass Media overcoat, worked so well to ensure the above characteristic features. The only drawback of glass media was that as a challenge inherent in glass media, the edge of outer periphery became “ski-jump” looking configuration; therefore, the head glide property would deteriorate near the outer edge. In order to reduce the “ski-jump” effect, polishing pad and process characteristics when fabricating the glass substrate were improved, and processing conditions were optimized. In addition to the use of glass media, this device adopted the most advanced technology such as, a 50-turn-coil high output thin-film head, sensorless spindle motor, Nd magnet VCM, 1-7 RLL Code recording mode, digital sector servo method, etc.

Now, let me summarize above-mentioned history briefly

1. 1989/10 Starts development design
2. 1990/ 3 Fundamental experiment begins by using functional samples
3. 1990/ 8 Device validation begins with functional samples
4. 1991/ 1 Qualification process begins with commercial samples and shipping to specific users
5. 1991/4 Volume production begins

As you see, Toshiba became a leader in the development of high-capacity 2.5-inch HDDproducts in rapid-fire succession by upgrading areal density and increasing the number ofinstalled glass disks.

Production History on 2.5” HDD with Glass Media and New Model

April 1991－

40MB（ 1 disk ）Model Volume Production Began
Approx.15K /Month

October 1991－

80MB（ 2 disks ）Model Volume Production Began
Approx.20K / Month including other models

March 1992－

131MB（ 2 disks ）Model Volume Production Began :
Approx.60K/ Month including other models

October 1992－

213MB（ 2 disks ）Model Volume Production Began :
Approx.70K/ Month including other models

May 1993－

340MB（ 3 disks ）Model Volume Production Began :
Approx.100K/ Month including other models

December 1993－

520MB（ 4 disks ）Model Volume Production Began :
Approx.150K/ Month including other models

September 1994－

704MB（ 5 disks ）Model Volume Production Began :
Approx.230K/ Month including other models

Shipment Growth

FY Shipped Volume Main Customers
1991 200K Pcs Internal Use, Domestic PC Maker
1992 780 K Pcs Domestic PC Maker
1993 1450 K Pcs Domestic, Taiwanese and US PC Maker
1994 2230 K Pcs All Over the World

Reference
Main Spec on the first 2.5 “HDD loaded with Glass media (MK 1122FC)

Capacity (Formatted) MB	43.0
Number of Disks	1 disk (Glass)
Number of Heads	2
User Cylinders	977
Sectors/Track	43
Bit Density (BPI)	51,891
Track Density (TPI)	2,000
Record Mode	1-7 RLL Code
Revolutions Per Minute (RPM)	3,200
Average Seek Time (ms)	23
Dimensions (mm)	70(W)x100(D)x17(H)
Weight (gr)	160
Environment
Vibration (Operating - G)	0.3
Vibration (Non-operating - G)	5
Shock (Operating - G)	5
Shock (Non-operating - G)	100
Number of CSS Cycles	40,000

Additional information

A number of other manufacturers experimented with glass substrates (e.g., SyQuest, Areal [1], [2] ) but none are known to have introduced them into commercial hard disk drives in any significant volume prior to Toshiba.

[1] Swartz, J, "New Areal 3½-in. Beats The Heat," Computer Technology Review, Feb 1989, p. 25
[2] Duffey, B, "Areal Taps CEO, to Stress 2.5-Inch Drives," Electronic News, Jul 23, 1990, p. 20

Provenance note: The article was authored by Fumitake Shiraishi, former Toshiba 2.5” HDD Development Director on or about January 30, 2008. G. Argentina arranged for the article to be written and then translated from Japanese. It was approved by the Computer History Museum's Storage SIG on May 28, 2012.